Tool 78: Reset every TCP packet

Description:

  This tool resets every TCP session matching a filter. It permits to
  temporarily block a TCP flow without having to change firewall rules.
  It also permits to force a renegotiation of session parameters, in
  order to sniff the beginning of connection.
  Parameter --device indicates on which device to sniff. Please note
  that under some systems, such as Windows, sniffing on some devices is
  not supported.
  Parameter --filter defines the sniff filter. It permits to restrict
  captured packets. This kind of filter is named a BPF or pcap filter.
  Basic elements of a filter are:
    host 1.2.3.4
    net 192.168.10
    net 192.168.10.0 mask 255.255.255.0
    net 192.168.10.0/24
    port 21
    dst host 1.2.3.4
    src port 2345
    ether host a:b:c:d:e:f ('ether a:b:c:d:e:f' is not working)
    ether src aa:bb:cc:dd:ee:ff
    ip
    arp
    rarp
    tcp
    icmp
    udp
  Here are filter examples:
    "host 1.2.3.4"
    "net 192.168 and icmp"
    "host 1.2.3.4 or dst port 80"
    "(udp or tcp) and not host 1.2.3.4"
  Parameter --spoofip indicates how to generate link layer for spoofing.
  Values 'best', 'link' or 'raw' are common choices for --spoofip. Here
  is the list of accepted values:
   - 'raw' means to spoof at IP4/IP6 level (it uses system IP stack). If
     a firewall is installed, or on some systems, this might not work.
   - 'linkf' means to spoof at link level (currently, only Ethernet is
     supported). The 'f' means to Fill source Ethernet address.
     However, if source IP address is spoofed, it might be impossible
     to Fill it. So, linkf will not work: use linkb or linkfb instead.
   - 'linkb' means to spoof at link level. The 'b' means to left a Blank
     source Ethernet address (0:0:0:0:0:0, do not try to Fill it).
   - 'linkfb' means to spoof at link level. The 'f' means to try to Fill
     source Ethernet address, but if it is not possible, it is left
     Blank.
   - 'rawlinkf' means to try 'raw', then try 'linkf'
   - 'rawlinkb' means to try 'raw', then try 'linkb'
   - 'rawlinkfb' means to try 'raw', then try 'linkfb'
   - 'linkfraw' means to try 'linkf', then try 'raw'
   - 'linkbraw' means to try 'linkb', then try 'raw'
   - 'linkfbraw' means to try 'linkfb', then try 'raw'
   - 'link' is an alias for 'linkfb'
   - 'rawlink' is an alias for 'rawlinkfb'
   - 'linkraw' is an alias for 'linkfbraw'
   - 'best' is an alias for 'linkraw'. It should work in all cases.
  
  This tool may need to be run with admin privilege in order to sniff
  and spoof.
   

Usage:

  netwox 78 [-d device] [-f filter] [-s spoofip] [-i ips]

Parameters:

parameter description example
-d|--device device device name Eth0
-f|--filter filter pcap filter  
-s|--spoofip spoofip IP spoof initialization type linkbraw
-i|--ips ips limit the list of IP addresses to reset all

Example:

  netwox 78